Kobe CHX9130SQB-WM-1 Instrukcja Obsługi Strona 1

KOBE Range Hoods Brillia Series Model No.

7 - Align and secure Top Vent Cover {E} and 3-1/4” x 10” Vent Cover (removed from rear exhaust) using 14 screws (13 screws taken from 6

8 Ductwork Installation 10. Use steel pipe to connect the exhaust on the hood to the ductwork. Use duct tape to make all joints secure and air tig

9 WALL MOUNT INSTALLATION ***This installation required to have Duct Cover Model No. CH1120DC-1. Preparation before Installation NOTE: TO AVOID

10 4. For Rear 3-1/4” x 10” vent installation only: - Remove attached 6” exhaust and discard. (Figure 11) Keep 13 screws to install ven

11 Wiring to Power Supply CAUTION: If moving the cooking range is necessary to install the hood, turn off the power in an electric range at

12 Install Accessories 15. Install the Oil Tunnel {G} into recess support near rear of hood. Refer to Figure 19. 16. Install Baffle Filters {H} an

13 OPERATING INSTRUCTIONS Note: For best results, turn fan on prior to any preparation or cooking and keep fans running while cooking. Adjust s

14 MAINTENANCE For optimal performance, clean the range hood surface and baffles regularly. To Clean Hood Surface CAUTION: NEVER USE ABRASIVE C

15 SPECIFICATIONS MODEL / SIZE Under Cabinet Application Wall Mount Application CHX9130SQB-1 (30”) CHX9130SQB-W

16 MEASUREMENTS & DIAGRAMS *** All inch measurements are converted from millimeters. Inch measurements are estimated. *** All measurements i

IMPORTANT READ THIS FIRST READ BEFORE INSTALLATION 1. Carefully check all contents of packages. 2. Thoroughly inspect the unit for any shipping dama

17 ***Hood-Mounting Bracket ***Duct Cover-Mounting Bracket ***Duct Cover Support

18 PARTS LIST MODEL NO.: CHX9130SQB-1 and CHX9130SQB-WM-1 (30”) CHX9136SQB-1 and CHX9136SQB-WM-1 (36”) NO. DESCRIPTION MODEL /SIZE PART NO. 1

19 MODEL NO.: CHX9130SQB-1 and CHX9130SQB-WM-1 (30”) CHX9136SQB-1 and CHX9136SQB-WM-1 (36”)

20 CIRCUIT DIAGRAM MODEL NO.: CHX9130SQB-1 and CHX9130SQB-WM-1 (30”) CHX9136SQB-1 and CHX9136SQB-WM-1 (36”)

21 TROUBLE SHOOTING Issue Possible Cause Solution After Installation, both motors and lights are not working. The power is not on. Make sure the c

22 WARRANTY WARRANTY CERTIFICATE In order to obtain warranty service, you must provide proof of original purchase from a KOBE authorized Deale

23 6. Product is purchased from an unauthorized KOBE dealer. 7. Product is damaged due to negligence, misuse, abuse, accident. If we determine tha

24 WARRANTY INFORMATION FORM Fill in the blanks and keep this paper with the original invoice in a safe place for future service purpose.

KOBE Range Hoods 11775 Clark Street Arcadia, CA 91006 USA www.koberangehoods.com This KOBE hood is made for use in the USA and CANADA

[ENGLISH] - READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...

1 IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

2 What to Do In The Event Of a Range Top Grease Fire • SMOTHER FLAMES with a tight fitting lid, cookie sheet, or metal tray, and then turn off the

3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) Range Hood Box Duct Cover Box (Included in Wall Mount Hood ONLY) CH1120DC-

4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to TA

5 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING, CLEANIN

6 UNDER CABINET INSTALLATION Preparation before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING.